HWQS 4-канальный адаптивный диммер для установки на DIN-рейку (LQSE-4A1-D)

Adaptive Power Module

The Adaptive Power Module family is a group of modular products for the control of lighting loads. This product is compatible with Lutron HomeWorks QS systems only. This document describes the following product:

• LQSE-4A1-D – 4 zone power module for phase control dimming.

Features

• Leading-edge or trailing-edge dimming for incandescent/ halogen, electronic / magnetic low-voltage, and neon / cold cathode light sources.

• Controls dimmable CFL/LED loads.

• RTISS Equipped® technology compensates for incoming line-voltage variations (up to ± 2% change in frequency/ second) such as changes in RMS voltage, frequency shifts, harmonics and line noise.

• Integral protection for temporary over-current and over-voltage conditions.

• SSL7 compliant for compatibility with Solid State Lighting.

• Includes QS link for seamless connection to a HomeWorks® QS system.

• LEDs on module provide diagnostic information.

• Buttons on module provide load override control.

• Manual Override Contact Closure Input (CCI).

• Power failure memory

Regulatory Approvals

• 120–240 V~ 50/60 Hz - UL® Listed - cUL® Listed - NOM Certified

• 220–240 V~ 50/60 Hz - IEC/EN 60669

Power

• 120–240 V~ 50/60 Hz (cULus and NOM)

• 220–240 V~ 50/60 Hz (IEC/EN 60669)

• Single input feed

• 4 A maximum total input current

• Lightning strike protection meets ANSI/IEEE standard C62.41 and IEC 61000-4-5. Can withstand voltage surges of up to 6 000 V~ and current surges of up to 3 000 A.

• ESD protected above agency requirements per IEC 60669-2-1

Environment

• For thermal specifications, see Output Zone Rating and Mounting section

• Relative humidity: less than 90% non-condensing

• For indoor use only Terminals

• Mains wiring: 1.0 mm? to 2.5 mm? (18 AWG to 12 AWG) (single wire, solid or stranded)

• CCI wiring: 0.5 mm? to 2.5 mm? (22 AWG to 12 AWG) (single wire, solid or stranded)

• Zone wiring: 1.0 mm? to 2.5 mm? (18 AWG to 12 AWG) (single wire, solid or stranded)

• QS Link: 0.5 mm? to 2.5 mm? (22 AWG to 12 AWG) (single wire, solid or stranded)

Manual Mode Operation

• By default, each zone is set to Auto Detect non-dim load type.

• Zone buttons on the unit can be used to: – turn loads on and off. – dim loads up and down when configured to a dimmed load type.

Output Zone Ratings

• No Derating is required if all the conditions below are met:

– Calibration point maximum is 70 ?C (158 ?F). – Room ambient temperature is between 0 ?C and 30 ?C (32 ?F and 86 ?F).

– Panel ambient temperature, within 20 mm (0.80 in) of unit, is between 0 ?C and 50 ?C (32 ?F and 122 ?F).

• 25 W (@120 V~)/50 W (@240 V~): Derating on all zones is required for a single module in a nonventilated enclosure if the room ambient temperature is between 30 ?C and 40 ?C (86 ?F and 104 ?F).

• 50 W (@120 V~)/100 W (@240 V~): Derating on all zones is required in a multiple row non-ventilated enclosure if the temperature is between 30 ?C and 40 ?C (86 ?F and 104 ?F).

• Each zone has a 5 W (incandescent) minimum load requirement.

• Does not support non-dimmable loads

• Automatically selects leading-edge or trailing-edge dimming when configured to "Auto-detect". It can also be configured for a specific load type.

• One load type per zone.

• This module is designed to control loads with ratings as noted in the table below. Outputs cannot be used to control general purpose receptacles.

Mounting

• Mount in IP20 (minimum) rated consumer panel or breaker panel with integrated DIN rail.

• For United States and Canada, use NEMA Type 1 minimum rated enclosure.

• Unit is 9 DIN modules (161.7 mm [6.37 in]) wide.